Have you ever daydreamed about being the ultimate handyman or woman? Is a person capable of tackling any home repair project with ease? Now, you can make that dream a reality – with just a drill and a few tips, you’ll be able to unlock your DIY potential by learning how to drill out a tubular lock. It’s easier than you might think and requires nothing more than some patience and knowledge.
What is a Tubular Lock?
Tubular locks are often preferred over traditional pin tumbler locks due to their relatively high level of security against picking or bumping attacks. They also tend to wear out less quickly than traditional pin tumblers, making them more suitable for long-term use.
Although they are not as secure as some higher-end locking mechanisms, tubular locks can provide an adequate level of protection in most situations. With proper maintenance, they can last many years without needing to be replaced.
For those looking for an extra layer of security, some tubular locks come with additional features such as tamper-proof screws and anti-drill plates, making them more difficult to bypass. Additionally, some models also have a key override feature that allows the user to override the lock in case of an emergency [1].
Tools and Materials Required to Drill Out a Tubular Lock
To drill out a tubular lock, you’ll need the following tools and materials:
- Small pin tumbler lock
- A quality drill bit set that includes drill bits sized for the lock. Most locks will require a 3/16” or 1/4” bit.
- Drilling lubricants such as oil, WD40, or graphite powder to help protect against heat buildup while drilling
- Masking tape to secure the drill bit in place
- Safety gear including goggles and gloves
- Hammer to help steady the drill bit if it begins to slip while drilling into the lock
- Tubular Lock pick (optional but helpful)
Once all your tools are gathered, you’re ready to begin drilling the lock. It’s important to use caution and take your time so that you don’t damage the lock or other parts of the door [2].
8 Easy Methods How to Drill Out a Tubular Lock
Drilling Out a Tubular Lock
- Gather all necessary tools: drill, safety glasses, tubular lock pick, lubricant (if needed), and a blank key that matches the lock you are drilling out.
- Put on safety glasses to protect your eyes from any flying debris while drilling.
- Insert the tubular lock pick into the back of the lock and attempt to turn it by turning it clockwise for 3-4 seconds. This will help loosen up any dirt or rust that may be preventing the lock from opening easily.
- If there is no success with the picking tool, then use a drill to start drilling slowly on one side of the back of the lock as straight as possible until there’s an indentation.
- Increase the speed of the drill and continue drilling around the circumference of the back of the lock until it’s completely drilled out.
- Once you have successfully drilled out the lock, insert a blank key into it and turn it counterclockwise to open it. If this is unsuccessful, then you can try using a different blank key or other locksmithing tools such as an extractor to remove the remaining pieces from inside the lock cylinder.
Using a Hand Drill
If you’re going to use a hand drill, it is important that you take your time and do not rush the process. Make sure that the bit of the drill is straight and in line with where you want to drill so as to avoid having crooked lines on the back of the lock.
Using an Angle Grinder
You can also use an angle grinder if you don’t have access to a drill or prefer using one due to its speed and power capabilities. When using an angle grinder, be sure to adjust its settings to a low speed and use the right disc attachment for metal such as a diamond blade. As with drilling, make sure that you don’t rush the process and take your time when using an angle grinder on a tubular lock so as to avoid damaging it.
Using Tubular Lock Picks
If all else fails, then you may also consider using a specialized tool called a tubular lock pick that is designed specifically for opening up these types of locks without having to drill them out. These tools are relatively simple to use and can be inserted into the back of the lock just like regular keys. Once inside, you maneuver the pick around until it can open up the internal pins within the cylinder allowing you to unlock it.
Using an Impact Driver
An impact driver may also be used for drilling out a tubular lock, however, this tool is more specialized and requires some background knowledge to use correctly. When using an impact driver, you need to adjust the settings so that the bit is spinning at a slower speed but with more torque than if it were being used in a standard drill configuration. This will ensure that you can penetrate through the lock without damaging it or risking personal injury due to over-drilling.
Using an Air Compressor
An air compressor can also be used to drill out a tubular lock. Air compressors are usually more powerful than regular drills or impact drivers and are designed to produce high pressure and torque which is perfect for drilling through tough materials such as metal locks. If you decide to use an air compressor, be sure to properly adjust the settings so that you don’t over-drill or damage the lock in any way.
Using an Oxygen Acetylene Torch
If you’re dealing with a particularly stubborn lock that can’t be drilled out or picked open, then you may consider using an oxygen-acetylene torch to burn away the metal to break it open. While this may seem drastic, it is a common practice among locksmiths and should only be done by experienced professionals with the right safety equipment and knowledge of how to handle these powerful tools.
Professional Locksmith
If all else fails, then the best option may be to call a professional locksmith who can come out and assess the situation and help you get your lock open without having to damage it. A professional locksmith will have the right tools and knowledge of how to safely operate them for opening tubular locks without causing any harm or destruction to the lock itself. At this point, you should now have a better understanding of how to drill out a tubular lock. Remember that if you feel uncomfortable doing this work yourself, it is always best to contact a qualified locksmith for assistance.
How to Drill Out a Tubular Lock
Step 1: Apply Masking Tape to the Drill Bit
Before you begin, apply some masking tape to the drill bit. This will keep it from slipping as you work and also help protect any delicate surfaces near the lock.
Step 2: Make a Hole in the Lock’s Center Using a Smaller Drill Bit
Use a small drill bit to make a hole in the center of the lock. Start with a size that’s much smaller than the core of the lock, such as 1/8 inch or 3mm.
Step 3: Apply a Larger Drill to Make a Second Hole Adjacent to the Already Completed One
After you’ve made the first hole, use a larger drill bit to make a second hole adjacent to the one that’s already been drilled. You can select any size bit as long as it is larger than the one used for the first hole. Keep in mind that this step is important because it will help cut through any hardened steel within the lock and allow you to access its core.
Step 4: Use an Even Larger Drill Bit
You can then use an even larger drill bit for the third hole directly next to the second one. This should be large enough to penetrate right through the lock casing and reach its core.
Step 5: Remove Any Remaining Lock Components
Once everything has been drilled out, use a pair of pliers or a screwdriver to remove any remaining lock pieces. Be sure to be careful as you work, so that you don’t cause any damage to the area around the lock.
Step 6: Insert a New Lock
Once all of the old components have been removed, it’s time to insert a new lock. You can select any type of tubular lock that is compatible with your specific needs. Make sure you follow all instructions for installation and enjoy your newly secured space [3]!
FAQ
Can you drill out a vending machine lock?
Yes, with the appropriate tools and knowledge, it is possible to drill out a vending machine lock. However, it’s important to note that this method is not recommended and can be illegal in some places. If you need to gain access to a vending machine, it would be best to contact the manufacturer or service provider for assistance.
How do you drill out a cylindrical lock?
To drill out a cylindrical lock, you will need to use a special type of drill bit called a cylinder-lock bit. These bits are designed to make an exact cut in the shape of the pin tumblers, allowing them to be bypassed and the door opened. It is important that you carefully select the right size bit for your particular lock as using too small or too large can damage it. Additionally, drilling out locks may be illegal in some places, so please check with local laws before attempting this method.
How do I open a locked vending machine?
The best way to open a locked vending machine is by contacting the manufacturer or service provider for assistance. They should be able to provide instructions on how to access the machine, as well as any other necessary information or tools. If that is not an option, then it may be possible to drill out the lock with the right tools and knowledge. However, this method is not recommended and should only be used as a last resort. Additionally, drilling out locks may be illegal in some places, so please check with local laws before attempting this method.
Does drilling out a lock work?
Yes, drilling out a lock can work in some cases. However, it is not always the best option and can be difficult to do correctly. Additionally, this method can damage the lock or door and may be illegal in some places, so please check with local laws before attempting this method. The best way to open a locked vending machine is by contacting the manufacturer or service provider for assistance. They should be able to provide instructions on how to access the machine, as well as any other necessary information or tools.
What type of drill bit is used for locks?
For locks, a special type of drill bit called a cylinder-lock bit is typically used. These bits are designed to make an exact cut in the shape of the pin tumblers, allowing them to be bypassed and the door opened. It is important that you carefully select the right size bit for your particular lock as using too small or too large can damage it. Additionally, drilling out locks may be illegal in some places, so please check with local laws before attempting this method.
Are there any alternatives to drilling a lock?
Yes, there are alternative methods for gaining access to a locked door or vending machine. Depending on the type of lock, picking or bumping tools may be used to open it without damaging it. Additionally, if you know the combination of the lock, then you may be able to unlock it manually. If none of these methods work or you do not want to risk damaging the lock, then it may be best to contact the manufacturer or service provider for assistance.
How easy is it to pick a tubular lock?
Picking tubular locks can be quite difficult and require specialized tools. These locks feature a unique design with pin tumblers that are positioned in a circle, making them more difficult to pick than traditional locks. Additionally, the pins must be picked in the correct order or they will not unlock. If you do not have experience picking these types of locks, it is best to contact a professional for assistance or use another method of gaining access such as drilling out the lock.
Are Tubular Locks Easy to Pick?
Picking tubular locks can be quite difficult and require specialized tools. These locks feature a unique design with pin tumblers that are positioned in a circle, making them more difficult to pick than traditional locks. Additionally, the pins must be picked in the correct order or they will not unlock. If you do not have experience picking these types of locks, it is best to contact a professional for assistance or use another method of gaining access such as drilling out the lock.
What drill bit should I use for cylinder locks?
For cylinder locks, you will need to use a special type of drill bit called a cylinder-lock bit. These bits are designed to make an exact cut in the shape of the pin tumblers, allowing them to be bypassed and the door opened. It is important that you carefully select the right size bit for your particular lock as using too small or too large can damage it. Additionally, drilling out locks may be illegal in some places, so please check with local laws before attempting this method.
Can I drill out a luggage lock?
Yes, with the appropriate tools and knowledge, it is possible to drill out a luggage lock. However, this method should only be used as a last resort and may not always work depending on the type of lock used. Additionally, drilling out locks may be illegal in some places, so please check with local laws before attempting this method. If you need to gain access to your luggage, it would be best to contact the manufacturer or service provider for assistance.
Useful Video: Successful Tubular Lock Drillout – Vending Machine
Conclusion
Drilling out a tubular lock is a difficult task that can be made easier with the right knowledge and tools. It is important to understand the basics of how tubular locks work before attempting drilling, so you can familiarize yourself with the different components and identify which one needs to be drilled out for a successful extraction. Additionally, it is essential to equip yourself with quality drill bits specifically designed for use on tubular locks. Taking these steps will help ensure that you have a successful experience when drilling out a tubular lock.
References
- https://unitedlocksmith.net/blog/what-is-a-tubular-lock
- https://toolsweek.com/how-to-drill-out-a-tubular-lock/
- https://revolar.com/drill-out-a-tubular-lock/
