Milwaukee M12 Drill Not Working: What to Do?

Milwaukee M12 Drill Not Working: What to Do? This is a question that plagues many Milwaukee M12 drill users. What should you do when your Milwaukee M12 drill stops working? Is the battery dead? Is there something wrong with the drill?

In this article, we will answer these questions and provide tips on how to fix your Milwaukee M12 drill.

Milwaukee M12 Drill Not Working: How to Fix?

If your Milwaukee M12 Drill is not working, there are a few things that you can do to try and fix the problem.

First, check to make sure that the batteries are properly installed and charged. If they are, then try resetting the drill by removing and then reinserting the batteries. If that doesn’t work, then you may need to replace the batteries.

Do a thorough check of the basics first

The first thing you should do when your Milwaukee M12 drill is not working is to check the basics.

This includes making sure that the batteries are properly installed and charged, that the drill bit is securely attached, and that there is no debris blocking the chuck. If the problem persists, move on to more specific troubleshooting steps.

Check the batteries

It may seem like a no-brainer, but making sure that the batteries are properly installed and charged is the first step you should take when troubleshooting a Milwaukee M12 drill that is not working. If the batteries are low on power, they will need to be recharged or replaced before the drill will work properly.

Clean the drill bit

Check the power switch

The power switch on the Milwaukee M12 drill may have been accidentally turned off. Make sure that the power switch is in the “on” position.

Make sure that drill is working

One of the most frustrating things that can happen while working with a power drill is when the drill suddenly stops working.

If you’re in the middle of a project and your Milwaukee M12 Drill stops working, it can be a real pain to have to stop what you’re doing and figure out what’s wrong.

There are a few things that you can do to try and troubleshoot a Milwaukee M12 Drill that’s not working:

• First, make sure that the drill is properly plugged in and that there is power going to it;
• If the drill is plugged in but still not working, try resetting the breaker or replacing the fuse;
• If the drill is getting power but still not working, the next thing to check is the switch. The switch may be faulty and need to be replaced;
• If the switch seems to be working properly, the problem may be with the motor. The brushes in the motor may need to be replaced or the armature may need to be replaced;

If you’re having trouble troubleshooting the problem yourself, you can always take the drill to a Milwaukee service center or authorized repair shop. They will be able to diagnose the problem and make the necessary repairs. [1]

Replace the chuck

If your Milwaukee M12 drill is not working, one of the first things you should check is the chuck. The chuck is the drill part that holds the drill bit in place.

Over time, the chuck can become worn out or damaged, making it difficult for the drill bit to stay in place. To replace the chuck, follow these steps:

1. Remove the drill bit from the chuck;
2. Use a chuck key to loosen the chuck;
3. Remove the old chuck from the drill;
4. Install a new chuck on the drill;
5. Tighten the chuck with the chuck key;
6. Insert a drill bit into the chuck and tighten it in place;

Fix the trigger

The trigger is what you press to start the drill. If the trigger is not working properly, the drill will not start. To fix a problem with the trigger, follow these steps:

1. Turn off the drill;
2. Remove the battery from the drill;
3. Use a small screwdriver to remove the screws that hold the trigger in place;
4. Remove the old trigger from the drill;
5. Install a new trigger on the drill;
6. Reattach the battery to the drill and turn it on;
7. Press the trigger to start the drill;

Quality Customer Care

If your Milwaukee M12 drill stops working, the first step is to check the power source. If the drill is plugged into an outlet, make sure that the outlet has power and is not locked out. If the drill is battery-operated, check the batteries and clean off any corrosion with a cotton swab dipped in vinegar.

If the power source is not the issue, then the next step is to check the drill chuck. The chuck is the drill part that holds the drill bit in place. To do this, first, remove the drill bit from the chuck.

Next, use a Chuck Key to loosen the jaws of the chuck by turning it counterclockwise.

Next, use a multimeter to test for continuity between the two terminals on the switch. If there is no continuity, then the switch will need to be replaced. [1]

FAQ

Why has my Milwaukee drill stopped working?

How do you unlock a Milwaukee drill?

If your Milwaukee drill is jammed or locked up, you can try the following to unlock it:

• Remove the battery and reattach it;
• Press and hold the trigger while turning on the power switch;
• Turn off the power switch and remove the battery, then press and hold the trigger while replacing the battery;
• If the drill still won’t unlock, contact Milwaukee customer service for further assistance;

What are some common causes of a Milwaukee drill not working?

There are several possible reasons why your Milwaukee drill might not be working:

• The battery may be dead or inserted incorrectly;
• The drill chuck may be loose or damaged;
• There may be something jamming the drill bit;
• The power switch may be turned off or defective;
• The motor may be burned out;

If you suspect any of these issues, it’s best to contact Milwaukee customer service for assistance.

How can I troubleshoot a Milwaukee drill that isn’t working?

If your Milwaukee drill isn’t working, there are a few things you can try to troubleshoot the issue:

• Check that the battery is inserted correctly and has enough charge;
• Tighten or replace the drill chuck if it’s loose or damaged;
• Clear any debris or obstruction from the drill bit or around the chuck;
• Make sure the power switch is turned on;
• If the drill still isn’t working, contact Milwaukee customer service for further assistance;

How do I take the battery out of my M12?

To remove the battery from your M12 Drill, follow these steps:

1. Remove the screw from the side of the drill using a Phillips head screwdriver;
2. Gently pull the battery out of the side of the drill;
3. You may need to use a flathead screwdriver to help release the battery from the side of the drill;

What do I do if my M12 won’t charge?

If your M12 Drill won’t charge, follow these steps:

1. Make sure the batteries are inserted correctly into the charger. The positive and negative terminals on the battery must match up with the positive and negative terminals on the charger;
2. Check the power source. Make sure the cord is plugged into a working outlet and that the outlet is not controlled by a switch;
3. Inspect the cord for damage. If the cord is damaged, it will need to be replaced;
4. Try charging a different battery in the charger. If the charger charges the second battery, then the first battery is likely defective and will need to be replaced;
5. If the charger still will not charge the battery, it may be defective and will need to be replaced;

How do I know if my M12 battery is bad?

There are a few ways to tell if your M12 battery is bad:

1. The battery will not hold a charge;
2. The battery will not power the drill;
3. The battery gets very hot when in use;
4. The battery swells up or leaks;
5. There is discoloration on the battery;

If you notice any of these signs, the battery is likely bad and will need to be replaced.

How do I clean my M12 Drill?

To clean your M12 Drill, follow these steps:

1. Unplug the drill from the power source;
2. Remove the batteries from the drill;
3. Use a soft cloth to wipe down the exterior of the drill. Be sure to avoid getting water on the drill;
4. Use a brush to remove any dirt or debris from the chuck of the drill;
5. Use compressed air to blow out any dust or debris from the interior of the drill;
6. Reassemble the drill and plug it into the power source;

My M12 Drill is not working properly, what should I do?

If your M12 Drill is not working properly, follow these steps:

1. Check the batteries. Make sure the batteries are inserted correctly into the drill and that they are charged;
2. Inspect the chuck. Make sure the chuck is tight and secure;
3. Check the power source. Make sure the cord is plugged into a working outlet and that the outlet is not controlled by a switch;
4. Inspect the cord for damage. If the cord is damaged, it will need to be replaced;
5. Try charging a different battery in the charger. If the charger charges the second battery, then the first battery is likely defective and will need to be replaced;
6. If the charger still will not charge the battery, it may be defective and will need to be replaced;

How do I prevent my M12 Drill from overloading?

To prevent your M12 Drill from overloading, follow these steps:

1. Use the correct drill bit for the material you are drilling;
2. Do not force the drill. Let the drill do the work;
3. Use a lower speed setting when starting to drill. Then increase the speed as needed;

Useful Video: Milwaukee M12 Blinking Lights Problem Fix

Conclusion

So, if your Milwaukee M12 drill isn’t working, there are a few things you can do before taking it in for repairs.

First, make sure the battery is fully charged and that the power switch is turned on. If it’s still not working after trying these two things, then check to see if something may be blocking the drill bit from rotating. Finally, if none of these solutions work, take your drill to a repair shop or contact Milwaukee customer service for assistance.

Hopefully, this article has helped you troubleshoot your Milwaukee M12 drill and get it up and running again!

References:

1. https://housetechlab.com/milwaukee-hammer-drill-not-working-5-solutions-for-you /